How to configure IP&MAC Binding on TL-WR802N/WR810N (standard router and hotspot router mode-new logo) 06-27-2022 31501 Keep the Available Host (IP/MAC) empty, which means you don’t specify any host to manage the router. Secondary Connection - It’s available only for PPPoE connection. If your ISP provides an extra connection type, select Dynamic IP or Static IP to activate the secondary connection. VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP or L2TP protocols to pass through the router’s firewall. bit - Enter 10 hexadecimal digits (any combination of 0-9, a-f and A-F. Null key is not permitted) or 5 ASCII characters.

Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty. Open Source Code For Programmers (GPL)

Alimentation électrique flexible - Facile à transporter en voyage 

How to Avoid Double NAT When DSL Modem Router and Wireless Router are Used Together 07-05-2022 105439

Priority - Priority of Bandwidth Control rules. ‘1’ stands for the highest priority while ‘8’ stands for the lowest priority. The total Upstream/ Downstream Bandwidth is first allocated to guarantee all the Min Rate of Bandwidth Control rules. If there is any bandwidth left, it is first allocated to the rule with the highest priority, then to the rule with the second highest priority, and so on. Wireless Radio - Indicates whether the wireless radio feature of the router is enabled or disabled. How to configure Bandwidth Control on TL-WR802N (standard router and hotspot router mode-new logo) 09-01-2022 41681 Move the router to a new location away from Bluetooth devices and other household electronics, such as cordless phone, microwave, and baby monitor, etc., to minimize signal interference.Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. How to set system time on TL-WR802N/WR810N (standard router and hotspot router mode-new logo) 06-27-2022 32017 Wireless Network Name - Enter a value of up to 32 characters. The same Name (SSID) must be assigned to all wireless devices in your network. If the service you want to use is not in the Common Service Port list, you can enter the corresponding parameters manually. You should verify the port number that the service needs. Channel Width - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. If you select auto, then AP will choose the best channel automatically.

Group Key Update Period - Specify the group key update interval in seconds. The value can be 0 or at least 30. Enter 0 to disable the update. L2TP Pass-through - Layer 2 Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the internet on the Layer 2 level. If you want to allow L2TP tunnels to pass through the router, you can keep the default (Enabled). Why cannot I access the Internet after successfully connected to the TP-Link router's wireless network(MAC OS)? 04-17-2019 503977

How to configure Wireless MAC Filtering on TL-WR802N/WR810N (except for client mode-new logo) 06-27-2022 32020 When a PC is set to be a DMZ (Demilitarized Zone) host in the local network, it is totally exposed to the internet, which can realize the unlimited bidirectional communication between internal hosts and external hosts. The DMZ host becomes a virtual server with all ports opened. When you are not clear about which ports to open in some special applications, such as IP camera and database software, you can set the PC to be a DMZ host. Port Range - The port range which the Interior PC access the outside PC. If all are blank or 0, the domain is noneffective. Enable Guest Network Bandwidth Control - If enabled, the Guest Network Bandwidth Control rules will take effect. Diagnostic is used to test the connectivity between the router and the host or other network devices.