Abwan Integrated Circuit, Coolrunner Rev C for Jasper Trinity Corona Phat & Slim Cable Xbox360 Pulse IC

Product Information

Glitch Chip Diagrams Phat CoolRunner rev C/D CoolRunner 3 Lite Matrix Glitcher Slim & E CoolRunner Rev C & CR3 Lite (Trinity) CoolRunner Rev C & CR3 Lite (Corona without Postfix) CoolRunner Rev C & CR3 Lite (Corona with Postfix) DGX v1.0S Programming the Glitch Chip Thanks, for reading! I hope this tutorial helped you in some way. This is probably the longest tutorial I have ever written so please let me know what you think about it, and if you think that I have missed something or that something needs more clarification.

Plug a flash drive into your Xbox 360 and navigate to Console Settings > Storage. Select the flash drive and allow the console to format the flash drive. Mostly up to date. I still need to add the points for Corona V5s and V6s and integrate the Slim Proto pictures instead of just linking to the TX forums but otherwise everything here is accurate. Plug the flash drive into your PC. Create a new folder on the flash drive and name it 0000000000000000 (16 zeroes). Open the new folder, then drag the CODE9999 folder into it. NOTE: If you have a Coolrunner Rev C and its addons instead of a Coolrunner Lite you will need to wire in the addons so I will go over these now. I know these pictures aren't the greatest but that is all there is on the net. Just remember that anywhere there is a solder pad that is on the edge of a QSB something most-likely needs to be soldered to it. The solder pads that are not on the edges are not used until later.There are a few different tools for reading your NAND chip: xFlasher 360, Nand-X, JR Programmer, Matrix USB NAND Flasher, PicoFlasher, various SD card tools, or a LPT cable. However, the 4GB Corona requires that you use an xFlasher 360, PicoFlasher, Element18592's 4GB USB tool, or an SD card tool. Consider the pros and cons below and choose the method that’s right for you. The LPT cable method is not recommended, as it's extremely slow, requires more work than other options, and cannot be used to program glitch chips. If your CB is on this list it is patched and not JTAG'able. If it is not on this list you are good to go.

Boot the console several times and ensure it boots consistently. If not, make sure your wiring is clean and neat and avoids noisy area. Run the wires near the X-Clamps for best results. Optional) An ethernet cable is plugged into the Xbox 360 and a LAN (e.g. a switch, router, or directly to a PC) If the console does not glitch reliably even after tuning the value, add a 68nf-100nf capacitor (ex: 683 cap or SMD cap) from PLL to GND. As I cannot remember ever single thing this list is somewhat incomplete and I will add to it as I remember or find new things that can be done Now that this is done you can close Nandpro and remove your LPT plug from your computer and your Xbox. We won't be needing it any longer. Also, unplug the Xbox's power.You can install XeXMenu to your hard drive by going to Console Settings > Storage, and copying it from your flash drive to the hard drive. Hey guys. Honestly I've been reading through threads here and elsewhere about how to mod my Trinity (as cheaply as possible - within reason). You may notice Step 0 and Step 3 have no explanations. This is simply because they are just parts you have to do and need no explanation.

LibXenon (runs in xell) based apps/emulators: http://libxenon.org/index.php?PHPSESSID=ja3u7k1skvj561qjg9t2ifsst5&board=8.0 Remove your NAND programmer wires and clean the points. Clean all flux off the board, allow it to dry, and test it once more before re-assembling. This wire wasn't in the previous picture, but you can see it in the overall one. It goes right next to the orange wire

Write a review

Open J-Runner and select ... next to the Load Source field and select one of your original NAND dumps if not already selected. In the upper right of J-Runner, ensure the Glitch2 radio button is selected.