Osmo 0.75L Polyx Hardwax Oil Satin 3032

Product Information

Natural oils accentuate the natural colour tone and grain of wood (permanent wet look). A dry Osmo Microfibre Roller can be used, if necessary, to roll out brush marks within 30 min of application.

Please Note: Oiled or waxed surfaces should not be cleaned with a steam cleaner or steam mop as these will degrade or potentially strip the oiled finish. Renovation A. In short, 'No'. Oiled and waxed finishes on floors are 'Micro-porous' which means that although the wood is protected, it can still breath as it is not completely sealed as it would be with a varnish. It seems there is a lot of confusion out there over the differences between all the Osmo products. I am asked all the time about how to choose which finish to use, and am constantly told the numbers just add to the confusion. And I totally get it. I felt the same way when first starting to use Osmo on my own projects. While I won’t be covering every single product Osmo makes, I can offer some guidance on the ones I do. I’ll try to make this as simple as possible. For daily maintenance, cleaning with a dry duster, floor mop or vacuum cleaner will be sufficient. For commercial premises, an electric floor polisher can be used. Wood surface must be clean and dry (moisture content max. 20%). Polyx®-Oil is ready to use, please do no thin, stir well before use.Based on natural vegetable oils and waxes (sunflower-oil, soyabean-oil, thistle-oil, carnauba-wax, candelilla-wax), paraffine, siccatives (drying agents) and additives. Disaromatised white spirit (benzene-free). This product fulfils EU-Regulation (2004/42/EC) according to the VOC limit value of max. 500 g/l (Cat. A/e (2010). Some woods are highly porous and require an especially thin application, as a result the drying time can be increased. Osmo Liquid Wax Cleaner can be used for refreshing the floor surface as required. If a higher level of sheen is desired, and after cleaning and thorough drying, apply the Liquid Wax Cleaner thinly and polish when dry. When dry, the finish is safe for humans, animals and plants (suitable for children's toys as per. EN 71.3 (European norm) and fast to perspiration and saliva in accordance with. DIN 53160 (German industrial norm)). Sand carefully before application starting with a coarse paper – final sanding for flooring P100-150, furniture P180-240. Remove dust etc. thoroughly from the surface before application (vacuum cleaner).

The final surface quality is dependent on the wood's surface structure, we therefore always recommend to test the product on a small sample area before complete application.. Cork tiles are best treated before fitting to avoid overlapping treatment of edges which would lead to prolonged drying times. A cork floor treated with Osmo Polyx-Oil will get a robust, elastic and wear-resistant surface which will harden further over 2-3 weeks. Due to the extreme absorption power of this highly elastic, natural, material we recommend the following procedure: The ideal application tool is a firm, fine, natural bristled brush. For the best results, apply thinly and remove any excess oil from the surface of the wood with a clean, lint-free cloth.Ideal for all wooden floors, solid or plank wood, strip parquet, OSB or cork flooring. Highly recommended for wooden furniture. Also for slate and screed as well as terracotta and other natural (non-glazed) ceramic tiles. Cleaning oiled or waxed floors with a steam cleaner or steam mop introduces high temperature and pressure water which can potentially degrade or strip the oiled or waxed finish. High pressure steam can also potentially damage wooden floors. Application of top coat of clear Osmo Polyx®-Oil Original can be carried out once the first coat has dried. However, if the first coat was a coloured Osmo finish ( eg Polyx®-Oil Tint or Wood Wax Finish Transparent) wait approx. 24hrs before applying Osmo Polyx®-Oil Original clear top coat. Floors finished with Osmo finishes are easy to clean, remove loose dirt with a soft brush or vacuum cleaner. Damp mopping is easy with Osmo Wash and Care, simply add to warm water (slightly moist mop only). For top coating Osmo white colours use white tinted Polyx Oils ( eg: 3040 or 3240) to avoid yellowing.

Looking for a long-lasting, natural finish for your wood flooring? Look no further than OSMO Polyx Oil Original. This hardwax oil is made from plant-based oils and waxes, making it environmentally friendly and easy to apply. Its durability and resistance to water, dirt, and wear make it perfect for high traffic areas, and it provides a natural, matte finish that will enhance the beauty of your wood flooring. Plus, its easy maintenance means you can enjoy your beautiful wood floor for years to come with minimal effort. Don't settle for a subpar finish – choose OSMO Polyx Oil Original for the ultimate protection and beauty for your wood flooring. Other household cleaning products such as vanish, bleach, baking soda etc. are likely to cause severe discolouration or staining. approx. 8-10 hours (normal climatic conditions, 23°C/50%, rel. humidity). Lower temperatures and/or high humidity can increase the drying time.

Also Recommended

Apply first coat very thinly with an Osmo Double Blade Scraper, or other suitable applicator for cork floors. For small projects, an Osmo Soft Tip Brush can be used Apply first coat thinly and evenly along the wood grain with an Osmo Floor Brush - use in conjunction with the Osmo Telescopic Handle for ease of application Cork flooring is highly porous and requires an especially thin application, as a result the drying time is increased (min. 24 hours per coat). Now we come to the Polyx family. I think this is the one that trips people up a bit. It is comprised of five individual products. Four are clear, and one is not. Let’s start with the one that is not - Osmo Effect/Neutral/Raw 3041 (I have seen it referred to all three ways which also adds to the confusion). It has a 2% white tint in it to counter the natural ambering of lighter woods, such as maple, ash, and white oak. You can use either 1 or 2 coats, depending on the look you are after. You will never get a truly white finish from it because it only has so much white in it. It has more of a matte finish to it and should be topcoated with a clear Osmo finish. I have used it on both maple and ash, and the wood looks almost bare afterwards. Always shake the can well before use. Failure to mix the white colour (within Osmo Door-Oil 3033 Raw) and all ingredients could lead to an increased patchiness.